Spectrum-controls 1756sc-OF8H Series A Manuel d'utilisateur télécharger pdf (Page 115)

Chapter 8: Ladder Program Examples 101

Rung 3 - This is an optional example rung indicating how to send on-the-

fly configuration data to the module. This is useful if you would like to

change channel alarm or scaling tags without causing interruption in

channel updates. Changing other tags will cause a 2.5 second delay in

channel updates but the connection will not be interrupted.

Continued on next page...

You may use either the SetAttributeAll or the Module Reconfigure

message.

1 2 ... 110 111 112 113 114 115 116 117 118 119 120 ... 169 170

Important Notes 3
Table of Contents 5
Table of Contents ix 9
Terms & 12
Abbreviations You 12
Should Know 12
Preface xiii 13
Module Overview 15
Chapter 1 15
System Overview 17
4 ControlLogix 18
Chapter 1: Module Overview 5 19
6 ControlLogix 20
Power Requirements 21
Using your module in 22
Module Installation and 22
Preventing 23
Electrostatic 23
Discharge 23
Removal and Insertion 23
Under Power 23
Compliance to 24
European Union 24
Directives 24
Wiring Your Module 26
Preparing and Wiring 27
Terminal Block Layout 28
Wiring Inputs to the 28
IF8H Module 28
Wiring Outputs to the 30
OF8H Module 30
18 ControlLogix 32
Operation Within the 33
ControlLogix System 33
Chapter 3Chapter 3 33
Chapter 3 33
Direct Connections 34
Module Operation 34
Modules in a Local 35
Requested Packet 35
Interval (RPI) 35
Modules in a Remote 36
Listen-Only Mode 36
Multiple Owners of 37
Input Modules 37
Configuration 38
Changes in an Input 38
Module with Multiple 38
Chapter 4 39
26 ControlLogix 40
Analog HART Modules 40
28 ControlLogix 42
30 ControlLogix 44
Configuration Tags 45
Overview 45
32 ControlLogix 46
Input Tags Overview 48
Output Tags 49
(OF8H Only) 49
36 ControlLogix 50
If8h0Configuration 52
Table 5.1b 53
40 ControlLogix 54
Table 5.1d 55
42 ControlLogix 56
Amplitude 57
44 ControlLogix 58
Table 5.3b 59
46 ControlLogix 60
1.) Select Controller Tags 61
3.) Select Monitor Tags 61
Click on the tag name of the 62
Configuration information is 62
1.) Highlight the value of 64
2.) Type in the valid new 64
Of8h0Configuration 66
Table 6.1b 67
54 ControlLogix 68
Table 6.1d 69
56 ControlLogix 70
Table 6.1f 71
58 ControlLogix 72
Table 6.2b 73
60 ControlLogix 74
Table 6.2d 75
Table 6.3 75
Use a pulldown menu 78
Pulldown menu 78
66 ControlLogix 80
68 ControlLogix 82
70 ControlLogix 84
72 ControlLogix 86
Table 7.1(Packet 0) 87
74 ControlLogix 88
76 ControlLogix 90
78 ControlLogix 92
Get HART Device Information 94
82 ControlLogix 96
HART Pass-Through Command 98
86 ControlLogix 100
Analog HART Modules 100
88 ControlLogix 102
90 ControlLogix 104
92 ControlLogix 106
94 ControlLogix 108
Short Frame Long Frame 109
Master to slave 02 82 109
Slave to master 06 86 109
96 ControlLogix 110
98 ControlLogix 112
Programming Examples 113
Chapter 8 113
100 ControlLogix 114
Set Attribute All message: 116
Module Reconfigure Message: 116
104 ControlLogix 118
106 ControlLogix 120
108 ControlLogix 122
110 ControlLogix 124
112 ControlLogix 126
114 ControlLogix 128
116 ControlLogix 130
Figure 5.6a (Packed ASCII) 131
118 ControlLogix 132
OK LED CAL LED Fault Status 133
122 ControlLogix 136
124 ControlLogix 138
126 ControlLogix 140
128 ControlLogix 142
Maintaining Your Module 143
And Ensuring Safety 143
Chapter 10 143
132 ControlLogix 146
HART Analog Modules 146
Appendix A 147
Environmental Conditions 148
Regulatory Compliance 148
Firmware Revision History 148
Appendix B 149
140 ControlLogix 154
142 ControlLogix 156
Appendix D 157
144 ControlLogix 158
146 ControlLogix 160
148 ControlLogix 162
150 ControlLogix 164
152 ControlLogix 166
Table 3c (First Byte) 167
Table 3d (Second Byte) 167
167
154 ControlLogix 168
Getting Technical 169
Assistance 169
Declaration of 169
Conformity 169

Commentaires sur ces manuels

Pas de commentaire

Spectrum-controls 1756sc-OF8H Series A Manuel d'utilisateur Page 115

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure Spectrum-controls 1756sc-OF8H Series A